- Dec 14, 2017 Roto-Die Hydraulic Bender Model 10 Hydraulic Press Brake 10 ft 16 ga FINANCING AVAILABLE Specifications: Bending Capacity, 7/8” die opening.
- Model 10 Roto-Die. The Model 10 Roto-Die is a 10-foot light gauge Hydraulic sheet metal bender and an industry standard for many HVAC duct shops. We proudly offer a wide selection of replacement parts for this versatile machine, including disappearing pin & spring assemblies, tie rods, ram return springs and foot pedal cables.
- Used Roto-Die Model #10 Press Brake (Like New) Contact for Pricing Production Products Inc. Has been providing labor saving machinery and innovative products to HVAC duct and sheet metal fabricators worldwide for over 25 years.
- Roto Die Hydraulic Benders. Roto Die Hydraulic Bender,Roto Die used.
A Roto-Die Hydraulic Sheet Metal Brake is as simple to operate as a hand brake - but has infinitely more production capacity. Model 10 Press Brake. The patented Roto-Die hydraulic sheet metal benders have been a fixture in thousands of sheet metal shops for over 45 years. Machine Specifications. The Model 10 Roto-Die is a 10 foot light gauge Hydraulic sheet metal bender is the industry standard for HVAC duct shops that want more capability than the Model 5 to form the standard range of rectangular HVAC duct, cross braking, produce custom fittings and sheet metal bending applications that come up in a contractor environment.
Instruction sheet, Gardner bender, Mini-eegor™ hydraulic bender
Advertising
The Mini-Eegor™ bender was designed with personal safety in mind. Nevertheless, when a
machine is powered with ten tons of force, certain precautions must be exercised to keep that force under control at
all times.
all times.
Fully Assemble All Load-bearing Pins:
Unless all pins are fully engaged in their respective sockets, the resulting misapplied loads can deform and destroy
the bender, with associated danger to attending personnel.
Unless all pins are fully engaged in their respective sockets, the resulting misapplied loads can deform and destroy
the bender, with associated danger to attending personnel.
1. All four axles of the compression roller plate assembly must project through, or be flush with, both plates.
2. The top aluminum load arm must be fully seated so that three pins project through it with the chamfered roller
2. The top aluminum load arm must be fully seated so that three pins project through it with the chamfered roller
engaging the slot.
3. The U-strap pin must seat on its handle.
Do Not Attempt to Use Damaged Components:
Should any part of the Mini-Eegor™ bender become
damaged for any reason, replace it before resuming
bending operations. Failure to do so may jeopardize other
components and personal safety as well.
Should any part of the Mini-Eegor™ bender become
damaged for any reason, replace it before resuming
bending operations. Failure to do so may jeopardize other
components and personal safety as well.
Keep Clear of Possible Pinch Points:
Relative motion between bender components could severely
pinch fingers or cut any objects wedged in between.
Relative motion between bender components could severely
pinch fingers or cut any objects wedged in between.
Use Standard Precautions with Hydraulic Hoses:
Couplings must be fully engaged to permit free flow of oil.
Be alert to avoid developing sharp bends or pinching
of hose.
Couplings must be fully engaged to permit free flow of oil.
Be alert to avoid developing sharp bends or pinching
of hose.
Bend Only Conduit that Fits Freely into Shoe Grooves:
Oversize pipe that hangs up on the groove edges can
sometimes split a shoe.
Oversize pipe that hangs up on the groove edges can
sometimes split a shoe.
Roto-die Hydraulic Bender Model 10 User's Manual Guide
Gardner
Bender
IMPORTANT RECEIVING INSTRUCTIONS: Visually inspect all components for shipping damage. If any shipping
damage is found, notify carrier at once. Shipping damage is NOT covered by warranty. The carrier is responsible for
all repair or replacement costs resulting from damage in shipment.
damage is found, notify carrier at once. Shipping damage is NOT covered by warranty. The carrier is responsible for
all repair or replacement costs resulting from damage in shipment.
Instruction
Sheet
Mini-Eegor™
Hydraulic Bender
IMPORTANT USER SAFETY AND PROTECTION: In setting up systems to fit your operations, care must be taken
to select the proper components and design to insure appropriate integration with your operations and existing
equipment and that all safety measures have been taken to avoid the risk of personal injury and property damage
from your application or system.
to select the proper components and design to insure appropriate integration with your operations and existing
equipment and that all safety measures have been taken to avoid the risk of personal injury and property damage
from your application or system.
GB ELECTRICAL CANNOT BE RESPONSIBLE FOR DAMAGE OR INJURY CAUSED BY UNSAFE USE,
MAINTENANCE OR APPLICATION OF ITS PRODUCTS. Please contact GB Electrical for guidance when you are
in doubt as to the proper safety precautions to be taken in designing and setting up your particular application.
MAINTENANCE OR APPLICATION OF ITS PRODUCTS. Please contact GB Electrical for guidance when you are
in doubt as to the proper safety precautions to be taken in designing and setting up your particular application.
To Protect Your Warranty, Use Only Enerpac Hydraulic Oil
Hydraulic
Coupling
Coupling
Follow Bar
Load Arm Pins
Hydaulic Cylinder
Rod Eye
Chamfered
Roller
Roller
U-strap
Top
Load Arm
Load Arm
Top Compression
Roller Plate
Roller Plate
U-strap Pin
Load
Arm Pin
4 Compression
Roller Axles
Roller Axles
Bending
Shoe
Shoe
Mini-Eegor™ Bender
Figure 1
This:
Results in this:
Advertising
Popular Brands
Popular manuals